SHANGHAI MCP CORP
Product Search
Product catalogue
POWER SUPPLY
TEST INSTRUMENTS
EDUCATION EQUIPMENT
METERS
MACHINE
ACCESSORIES
Product Detail
ACL-7000 
Details

ACL-7000
ANALOG CIRCUIT LABORATORY


Features

.Four circuit boards form 22 experiments.
.Ideal tool for learning the basics of analog circuits.
.Step-by-step exercises and application.
.Integrated training system, with complete <INSTRUCTION>.
.Combination with M21-7000 digital-analog training system as main unit.
.Step-by-step exercises and application.
.Expandability and flexibility of experiments greatly
increased by large breadboard.
.Boards can be changed easily.

The ACL-7000 analog circuit laboratory is a comprehensive and selfcontained system suitable for tuition and experimentation with a range of analog electronics circuits. All necessary equipments such as power supply, signal generator, switches and displays are built-in on the main unit. The 6 circuit boards cover a wide variety of essential topics in the field of analog electronics. It is a time and cost saving device for both students experiment and researchers interested in developing and testing circuit prototypes.


THE FULL LIST OF EXPERIMENTS PERFORMED USING DTS-011 ~ DTS-016

Experiment 1
Experiment 2
Experiment 3
Experiment 4
Experiment 5
Experiment 6
Experiment 7
Experiment 8
Experiment 9
Experiment 10
Experiment 11
Experiment 12
Experiment 13
Experiment 14
Experiment 15
Experiment 16
Experiment 17
Experiment 18
Experiment 19
Experiment 20
Experiment 21
Experiment 22
Monopole Amplifying Circuit
Two Stage Amplifier Circuit
Negative Feedback Amplifier Circuit
Emitter Follower
Differential Amplifier
Scaling Summing Amplifier
Integrator and Differentiator Amplifier
Waveform Generator Circuit
Active Filter
Voltage Comparator
Wien Bridge Oscillator
Integrated Power Amplifier
Rectifier Filter and Parallel Regulation Circuit
Series Regulation Circuit
Integrated Voltage Regulator
RC Oscillator
LC Oscillator and Frequency-selective Amplifier
Current/voltage Conversion Circuit
Voltage/frequency Conversion Circuit
Complementary Symmetry Power Amplifier
Waveform Conversion Circuit
FET Amplifier



MAIN UNIT M21-7000

SOLDERLESS BREADBOARD


Interconnected with 2820 tie points nickel plated contact,fitted all DIP sizes and all components with lead and solid wire AWG # 22-30 (0.3-0.8mm).It can be changed and replaced for different purpose and can be connected with demonstration panel. Therefore, it is very convenient for both teachers and students.
DC POWER SUPPLY
A. Fixed DC output+5V, 1A
B. Fixed DC output-5V, 1A
C. Variable DC output0V to +15V, 1A
D. Variable DC output0V to –15V, 1A

POTENTION METERS

A. Variable resistor VR11kΩ
B. Variable resistor VR2100kΩ
FUNCTION GENERATOR
Frequency range1Hz-10Hz
10Hz-100Hz
100Hz-1kHz
1kHz-10kHz
10kHz-100kHz
Amplitude Sine wave output:0-10 Vpp variable
Triangle wave output:0-10 Vpp variable
Square wave output:0-10 Vpp variable
TTL mode output:4 Vpp

TWO DIGITS OF 7 SEGMENT LED DISPLAY

TWO PULSE SWITCH2 pcs pushbuttons contain switches debouncer for eliminating the bounce caused by switch from“open” to“close” or from“close” to“open”position.
SIXTEEN DATA SWITCHES16pcs toggle switches and corresponding output point. When switch is set at “down”position,the output is LO level; contrarily, it is to be HI level while setting at “up”position.
SPEAKER2-1/2 inch diameter, 8 ohm/0.5W to be used for load.
FOUR CHANNEL ADAPTORBoth of the two banana sockets' and two BNC jacks' point tips are changeable. It is suitable for M21-7000 to be connected with peripherals.
SIXTEEN BITS LED DISPLAY16 red LED's separate input terminals. The LED will be lighted up when input is at “HI level” ,and it will be turned off when it is at no input or at “LO level”.
UNIVERSAL CONNECTOR FIXED HOLDER
It reserves universal connector fixed holder on the panel in order to be connected with various universal connectors,
which are available
(1) Straight header 60 pin
(2) Card edge connector 2.54mm 62pin
(3) D sub25 pin connector, male & female
(4) Card edge connector 3.96mm 56pin
(5) Dip sockets connector 28 pin & 40 pin


1. Accessories
(1) Power cord
(2) Pin leads: 10cm 20pcs, 20cm 20pcs
(3) User manual+ instruction of analog circuit experimentations

2. INPUT VOLTAGE: 110~127VAC±10% 60Hz, 220~240VAC±10% 50Hz Switchable

3. DIMENSIONS:
(1) Main unit (W×H×D): 258×95×334mm
(2) Circuit board: 165×170mm

4. WEIGHT:
(1) Main unit: 4.5kg
(2) Circuit board: 0.4kg×6